Skip to main content

Bench power supply project

I found myself needing a 480W power supply to test a high current project I was working on. A 500W bench/lab power supply will set you back $100s so I figured a PC power supply was the cheapest bet. For $80 you can get a Wonhunglow brand. I checked ebay and found Dell 500W server power supplies CHEAP. Like $2 cheap.

I acquired a couple and figured out how to turn the thing on by shorting 3 pins together. Then I designed a simple little 4 rail power supply PCB and had it built by OSH Park. This power supply outputs 12V and 5V and 4V. I didn't have any use for the 4V so I skipped those pins but did add a 500mA 3.3V LDO to my board so I have 3.3V, 5V, 12V, and GND rails available. I left a large section of the solder mask missing so I could solder on some more current carrying capacity and called it done. I used a DPDT switch to short out the 3 pins required to turn on the 12V rail and added a little LED to indicate that the 3.3V regulator was running and put a small current limiting resistor on the LED so that the regulator is stabilized (I didn't check the datasheet too closely but it is common for an LDO to behave strangely until it has a minimum load). One minor complicating factor was the unusual connector on this hot swappable power supply. It had a part number on it though and I was able to get Molex to send me a couple mating adapters.

I will redesign this with a fully adjustable constant voltage and constant current output in the the future. That will be a bit of a project because 500W is a lot of power to bleed off and I want it to be accurate so I plan to use 12bit DACs and ADCs. I've been looking around for them and they are expensive enough that I think I will just use a ARM Cortex 3 microcontroller with on board 12 bit converters. More on that on some future post.

Here it is.
The business end.
Plugged into the Power Supply
Side view of the Power Supply with PCB attached
The back side featuring the LDO and Molex connector.

Comments

Popular posts from this blog

A Capacitive-Touch Janko Keyboard: What I Did at the 2017 Georgia Tech Moog Hackathon

Last weekend (February 10-12, 2017) I made a Janko-layout capacitive-touch keyboard for the Moog Werkstatt at the Georgia Tech Moog Hackathon. The day after (Monday the 13th), I made this short video of the keyboard being played: "Capacitive Touch Janko Keyboard for Moog Werkstatt" (Text from the video doobly doo) This is a Janko-layout touch keyboard I made at the 2017 Moog Hackathon at Georgia Tech, February 10-12. I'm playing a few classic bass and melody lines from popular and classic tunes. I only have one octave (13 notes) connected so far. The capacitive touch sensors use MPR121 capacitive-touch chips, on breakout boards from Adafruit (Moog Hackathon sponsor Sparkfun makes a similar board for the same chip). The example code from Adafruit was modified to read four boards (using the Adafruit library and making four sensor objects and initializing each to one of the four I2C addresses is remarkably easy for anyone with moderate familiarity with C++), and

Freesiders Hackers Collaborate in Medical / Surgical Research

Published in the May issue of the Journal of Foot and Ankle Surgery : " A Novel Combination of Printed 3-Dimensional Anatomic Templates and Computer-assisted Surgical Simulation for Virtual Preoperative Planning in Charcot Foot Reconstruction ." This collaboration of specialties represents an undertaking by members of Freeside Atlanta , Southern Arizona Limb Salvage Alliance , and The Podiatry Institute .  Charcot foot reconstruction remains on of the most challenging procedures in foot and ankle surgery.  These procedures are often lengthy procedures which can be riddled with complications. With the help of Freeside Atlanta Members, institutional researchers used open source Osirix Image viewer and 3D Software such as Newtek's Lightwave or Blender to create simulated surgical reductions as well as 3D printed templates.  Freeside Atlanta members assisted in providing 3D printing solutions and know-how to the project. Experimental test prints were done on a M

Onboard Firmware of the Human Brain

Freesiders are continually tinkering with robotics and other such machinery .  Many of these embedded processors and firmware are becoming open source and every-more diversified in the wake of the modern Maker movement . One notable boost to the hackerspace arsenal is the Arduino (an like platforms).  This offers designers an incredible power to devise not just individual devices but even the emergence of complex, integrated systems . This evolutionary pace of modern technological systems may be significantly faster the biologic system development, but there may be a few well learned tricks yet to be mastered.  It seems that studying how nature has managed to solve many development challenges will aid in designing robotics, where efficiently counts just as much. One  challenge, that is particularly interesting, is data processing.  Artificial intelligence is labored with processing data and producing a meaningful and useful output.  When considering the increase in sensory