Skip to main content

A Portable Storage System for Dead Tree Information Storage (Bookcase)


I (Ben Bradley) have made several of these for my personal use. My early bookcases were three feet wide, but moving was a process of putting books into boxes, moving the shelving and the boxes, and putting the books back on the shelves. It was unknown whether the bookcase would hold together if tilted while fully loaded, because it was too heavy to pick up when fully loaded

This one was assembled at Freeside after the November 5 Open House and is based on my current design, as follows:

Components used (available at any Home Depot or Lowes):
(4) 1" x 8" x 6 ft pine board (actual measurements 3/4" x 7 1/4")
(1) 4 ft by 8 ft. x 1/4" plywood board.
(48) 2" long wood or drywall screws, coarse thread preferred (about half of a 1 lb box)
(30) 1" long wood or drywall screws, coarse thread preferred (about a tenth of a 1 lb box)


Tools used:
Chop saw, table or circular saw, hand sander, electric drill/electric screwdriver (two preferred, one for drilling and one for screwing), 1/8" or 5/32" drillbit, clamp that opens to 19"

Assembly:

Compare the lengths of the 6-foot boards. They can differ by 1/4 inch or more. Choose the two longest for the sides. If their lengths are different, cut the longer one to match the shorter one.

Cut the two remaining ones into eight equal-length pieces. The length of 17 3/4 works well as it gives enough space for the saw kerf and a little extra for variations in length.

Sand one side of each of these (this will be the top side where books rest on it), and on one long edge, sand a "curve" along the edge so it is rounded off. Alternately, use a roundover bit in a router to round this edge.

Put the side edge of the first or "bottom" shelf piece against the side of one of the side pieces at one end. A clamp may help here. The rounded edge should NOT be next to the bottom of the side.

The diameter of the hole drilled for screws depends on the screw size used. Older projects used #6 drywall screws, where a 1/8" drill bit work well, but the Home Depot used for parts for this project only had #6 (slightly larger) screws, and a 5/32" bit was used successfully.

Drill a hole about one inch from the front or back edge so that it goes through the side and into the shelf piece equidistant from the top and bottom (for a 3/4" shelf this will be 3/8" from the edge, but I always eyeball it as the center - it's good enough), and into the wood about as far as the screw will go, or perhaps 1/4" less than the screw (set the drikk into the chuck to extend this distance). Be sure to drill straight, so the hole is parallel to the shelf and the screw won't come through.

Screw the screw in, using a drywall screw setter bit. This is a Phillips bit with a metal ring around it that will cause the bit to slip out of the screw once it is just below flush with the wood. This gives excellent strength and prevents accidentally screwing the screw too far into the side, which is easily done with an electric drill/screwdriver.

Drill a second hole the same one inch distance from the other side and put a screw in it. Drill a third hole midway between the other two and put a screw in it. I do it in this order as it's easier to eyeball the middle of the board near the edge, and then it's easier to make the hole in the middle midway between the other two that are already drilled.

Drill the other side of the shelf to the other side piece as above, so that the two side pieces are parallel.

Make two "spacer" pieces of wood using scrap (such as a length of 1" x 8" or smaller), exactly 9 3/4" long. This will be the distance between shelves, and determines the height of the books that will fit between the shelves. Be sure the top and bottom edges of these pieces are parallel, as this is needed for the shelves to all be horizontal.

Put the two spacer pieces along the side pieces and touching the bottom shelf, and place a second shelf between the sides so it touches the other ends of the spacers. This gives a precision height to the shelf without measuring. Make sure the rounded over edge of the shelf is on the same side as the rounded over edge of the bottom shelf. Drill holes and use screws to attach this shelf. Pull out the spacer pieces. They may be moderately tight, but can usually be removed by hand.

Continue attaching shelves in this way until you get to the top shelf. Align the top of the top shelf with the tops of the side pieces, and drill and screw it.

Cut the 4' x 8' by 1/4" plywood to the dimensions of the back of the bookcase, which should be about 19 1/4" x 6 feet. Align it with the back (the side opposite the rounded over shelf edges), and attach it using 1" screws spaced about every six inches.

This bookcase is for Octavo sized books, and the top shelf is just large enough for mass-market paperback books. I've made a similar shelf that fits (almost?) all Quarto sized books and magazines with 1" x 10" boards cut about 14" wide (five shelves per 6-foot plank, seven shelves per bookcase) and with 11 3/4" spacing between the shelves.

These bookcases may weigh 200 lbs fully loaded, but can be moved by one person with a handtruck. Push on the side until the bottom lifts up, put down on the handtruck, then pull back with one foot on the handtruck axle, and move while balanced as shown in the photograph. It can lay down in a pickup truck bed, or stand up in a tall enclosed truck with it tied to the walls.

Comments

Popular posts from this blog

A Capacitive-Touch Janko Keyboard: What I Did at the 2017 Georgia Tech Moog Hackathon

Last weekend (February 10-12, 2017) I made a Janko-layout capacitive-touch keyboard for the Moog Werkstatt at the Georgia Tech Moog Hackathon. The day after (Monday the 13th), I made this short video of the keyboard being played: "Capacitive Touch Janko Keyboard for Moog Werkstatt" (Text from the video doobly doo) This is a Janko-layout touch keyboard I made at the 2017 Moog Hackathon at Georgia Tech, February 10-12. I'm playing a few classic bass and melody lines from popular and classic tunes. I only have one octave (13 notes) connected so far. The capacitive touch sensors use MPR121 capacitive-touch chips, on breakout boards from Adafruit (Moog Hackathon sponsor Sparkfun makes a similar board for the same chip). The example code from Adafruit was modified to read four boards (using the Adafruit library and making four sensor objects and initializing each to one of the four I2C addresses is remarkably easy for anyone with moderate familiarity with C++), and

Freesiders Hackers Collaborate in Medical / Surgical Research

Published in the May issue of the Journal of Foot and Ankle Surgery : " A Novel Combination of Printed 3-Dimensional Anatomic Templates and Computer-assisted Surgical Simulation for Virtual Preoperative Planning in Charcot Foot Reconstruction ." This collaboration of specialties represents an undertaking by members of Freeside Atlanta , Southern Arizona Limb Salvage Alliance , and The Podiatry Institute .  Charcot foot reconstruction remains on of the most challenging procedures in foot and ankle surgery.  These procedures are often lengthy procedures which can be riddled with complications. With the help of Freeside Atlanta Members, institutional researchers used open source Osirix Image viewer and 3D Software such as Newtek's Lightwave or Blender to create simulated surgical reductions as well as 3D printed templates.  Freeside Atlanta members assisted in providing 3D printing solutions and know-how to the project. Experimental test prints were done on a M

Onboard Firmware of the Human Brain

Freesiders are continually tinkering with robotics and other such machinery .  Many of these embedded processors and firmware are becoming open source and every-more diversified in the wake of the modern Maker movement . One notable boost to the hackerspace arsenal is the Arduino (an like platforms).  This offers designers an incredible power to devise not just individual devices but even the emergence of complex, integrated systems . This evolutionary pace of modern technological systems may be significantly faster the biologic system development, but there may be a few well learned tricks yet to be mastered.  It seems that studying how nature has managed to solve many development challenges will aid in designing robotics, where efficiently counts just as much. One  challenge, that is particularly interesting, is data processing.  Artificial intelligence is labored with processing data and producing a meaningful and useful output.  When considering the increase in sensory