Skip to main content

Building an enclosure for the LulzBot AO 100

As the cold weather season arrives in Atlanta, with it comes issues with our 3D printers. Specifically problems with temperatures and print stability.

Freeside is essentially a big warehouse, and our 3D printing station is setup in the large open area in the front of the space. What this means is that when it is cold in the space, this will affect the printing quality because the ambient temperature is far lower than what is optimal for thermoplastics. The cold ambient air will cause parts to rapidly cool during the middle of a print. And with materials like ABS which can shrink dramatically during cooling, this causes prints to warp, deform, and delaminate during and after printing is finished.

The print on the left is showing signs of delamination from plastic cooling mid print.

To remedy this, we built an acrylic enclosure for our LulzBot AO-100, which is our dedicated ABS printer.

We tested the proof of concept of whether an enclosure would help mitigate printing problems by sticking a big cardboard box on the LulzBot to trap heat in. We also tried pushing hot air into it using a heatshrink heat gun, which turned out to actually cause the temperatures to be too high and 3D prints suffer problems on the other end of the spectrum.

The LulzBot sitting inside the shame box.

Print affected by ambient temperature being too high.

Removing the heat source made the printer spit out great quality prints, and we then moved on to building the acrylic enclosure. There is a lot of scrap materials at Freeside, including several large sheets of 1/8" and 1/4" clear acrylic. Using the outer dimensions of the LulzBot (and adding a couple inches for safety), we drew up a quick design, and cut the acrylic on the table saw.

The acrylic panels were aligned and clamped together using scrap pieces of wood, and the acrylic was bonded using acrylic glue. We also 3D printed hinge and corner pieces that we found on Thingiverse to help add support.

Always be clamping!

Two holes were drilled into the box, one in the top for the filament to feed through, and one in the back for the power and USB cables to enter into the box. The door was affixed using 3D printed hinges, model grade cyanoacrylate which melts and bonds ABS and acrylic, and a short piece of 3mm filament used for the actual hinge.

The LulzBot looking like a piece in an art exhibit.

All together the build took less than 2 days from start to finish. We need to dial in our printer settings - we had raised the extruder temperature profiles to compensate for the cold ambient air - but things are already printing much more reliably. We were uncertain if we needed some sort of heating element, but it seems that the heat put out by the extruder and the heated bed are enough to keep the inside of the enclosure warm enough for quality printing.


The next order of business will be adding a temperature sensor and an exhaust fan for when things get too warm, but that will be a project for another day!

Comments

Popular posts from this blog

A Capacitive-Touch Janko Keyboard: What I Did at the 2017 Georgia Tech Moog Hackathon

Last weekend (February 10-12, 2017) I made a Janko-layout capacitive-touch keyboard for the Moog Werkstatt at the Georgia Tech Moog Hackathon. The day after (Monday the 13th), I made this short video of the keyboard being played: "Capacitive Touch Janko Keyboard for Moog Werkstatt" (Text from the video doobly doo) This is a Janko-layout touch keyboard I made at the 2017 Moog Hackathon at Georgia Tech, February 10-12. I'm playing a few classic bass and melody lines from popular and classic tunes. I only have one octave (13 notes) connected so far. The capacitive touch sensors use MPR121 capacitive-touch chips, on breakout boards from Adafruit (Moog Hackathon sponsor Sparkfun makes a similar board for the same chip). The example code from Adafruit was modified to read four boards (using the Adafruit library and making four sensor objects and initializing each to one of the four I2C addresses is remarkably easy for anyone with moderate familiarity with C++), and

Freesiders Hackers Collaborate in Medical / Surgical Research

Published in the May issue of the Journal of Foot and Ankle Surgery : " A Novel Combination of Printed 3-Dimensional Anatomic Templates and Computer-assisted Surgical Simulation for Virtual Preoperative Planning in Charcot Foot Reconstruction ." This collaboration of specialties represents an undertaking by members of Freeside Atlanta , Southern Arizona Limb Salvage Alliance , and The Podiatry Institute .  Charcot foot reconstruction remains on of the most challenging procedures in foot and ankle surgery.  These procedures are often lengthy procedures which can be riddled with complications. With the help of Freeside Atlanta Members, institutional researchers used open source Osirix Image viewer and 3D Software such as Newtek's Lightwave or Blender to create simulated surgical reductions as well as 3D printed templates.  Freeside Atlanta members assisted in providing 3D printing solutions and know-how to the project. Experimental test prints were done on a M

Onboard Firmware of the Human Brain

Freesiders are continually tinkering with robotics and other such machinery .  Many of these embedded processors and firmware are becoming open source and every-more diversified in the wake of the modern Maker movement . One notable boost to the hackerspace arsenal is the Arduino (an like platforms).  This offers designers an incredible power to devise not just individual devices but even the emergence of complex, integrated systems . This evolutionary pace of modern technological systems may be significantly faster the biologic system development, but there may be a few well learned tricks yet to be mastered.  It seems that studying how nature has managed to solve many development challenges will aid in designing robotics, where efficiently counts just as much. One  challenge, that is particularly interesting, is data processing.  Artificial intelligence is labored with processing data and producing a meaningful and useful output.  When considering the increase in sensory